STAINING & FINISHING TREADS

It seems that current design trends, imply that more than 90% of all the mouldings and stair treads that we sell these days are stained a colour darker than their natural tone. So let me offer a few thoughts on how to get the job done and get some awesome results.

Step #1: Sanding

Although all of our treads have undergone automated sanding it is essential that you fine-sand the edges and the top face one more time, to get the most uniform absorption of stain. This is particularly critical with difficult woods to stain, like hard maple. Some of my clients that do furniture restoration suggest that sanding to 320 or 400 will eliminate ALL of maple's staining challenges, but then I might need drugs to be that patient!

The flat face of each tread has been sanded to 120 grit and feels and looks pretty smooth. The bullnose on the front and possibly, if you ordered it that way, the bullnosed on the end has been created with a shaper cutter. Thus the rounded edges and the top face are not the same, one has a "cut" edge and one has a "sanded" face. Each will absorb stain differently.... and that is not even considering the challenges of the end grain.

So we need to sand, in the direction of the grain all edges, ends and faces to 180 grit.. if its maple I'd probably aim for 220. And don't cheap out on the sandpaper. Go to your local automotive supply house and buy good automotive sandpaper. It will make all the different, and for the extra 30 cents a sheet eliminate a lot of frustration.

Then the key is to remove all the dust, even that that hides in the pores of the wood. Use a blow gun, vacuum or tack cloth, whatever you have available.

Step #2: Staining

Experiment first. Don't assume stains out of the can will be exactly as shown, especially water based stains. Sometimes you have to dilute the stain and sometimes you need two coats, so stain a small sample AND apply the intended clear coat FIRST to see if you get the shade you are after. ONLY then proceed with the real stuff.

Brush or wipe on the stain, moving quickly across the surface. If it is an open pore wood like ash or oak it is important to go cross-grain and work the stain into the pores. To finish use a clean cloth rubbing WITH the grain to remove all the excess. No stain should puddle on the surface.

The small little "stain pillows" are worth the two dollar price tag. They load up with lots of stain, let you move fast (important with water based stains particularly) and stretch the coverage more than any cheap recycled T-shirt. They're a great investment and make your job much more pleasant.

Let the stain dry as per the instruction and re-apply if you need to darken further.

Step #3: Top Coat

Today you still typically get a choice between water-based and/or oil-based polyurethane. I must admit I still like the handling characteristics of the oil-based better, even though I recognize they're a pain when you have to wait 4 hours for drying so make a choice. You'll not find two people that agree to which is the best product to use.

Water-based: Dries fast, less smell but foams and raises the grain. Non-yellow, particularly great in cases where you are trying to maintain as light of a colour as possible.. as in natural maple.

Oil-based: Flows better, most are more durable especially if compared to cheap water based (my opinion, not scientific), takes too long to dry and does have a YELLOW TING .. so you have to take that into consideration when colour matching.

OK, so I've expressed my bias! Either way always whenever possible flat finish BEFORE installation, put on FOUR good coats of finish so you'll never have to crawl up and down your steps and do this again in your lifetime.

Sand gently between coats 2 and 3 with 220 paper and between coats 3 and 4. Use a block for the flat face, and a soft pad for the rounded edges.

Note: Do not use lacquers as they are considered too brittle for horizontal applications where you want the finish to "indent" or "flex" with abuse rather than scratch off.

I hope this helps to get you going.

Click HERE for information on Hardwood Stair Treads, ordering information, what different types of wood are available and even help with installation... or if you would like to see a few jobs that we have completed check out these photos of hardwood stairs in our gallery

Save to:

| Privacy Policy | Terms of Use