| Lacasse Fine Wood Products Inc. | search our site |
      |
WOOD RAILING COMPONENTS
All these wood railing components are carried in stock in maple and oak, and occasionally in birch and some items in white pine.
The grooved handrails are designed to fit with our 1 5/16" or 1 3/4" balusters to create a integrated selection of railing parts, so if you are trying to combine this with some old spindles in a renovation project be careful to check the dimensions to make sure the size of the groove will work with your spindles.
#4000 2 5/8" Colonial Handrail (grooved for 1 5/16" spindles)
Size: 3/4" x 2 5/8"
Groove: 1 5/16" for small colonial or square spindles
Lengths: 3-12', occasionally 14'-16' long
Wood Species Available In Stock: Oak, Maple (this is the most common railing we make)
#4210 Small Filler
Size: 1/2" x 1 5/16"
Lengths: 2-12' long
Matching Handrail: to fit handrail #4000, 4900 & shoe rail #4230
#4001 3" Colonial Handrail (grooved for 1 3/4" spindles)
Size: 1 3/4" x 3"
Lengths: 2-12', occasionally 14'-16'
Groove: 1 3/4" for large colonial spindles
Wood Species Available In Stock: Oak, Pine, Maple
#4211 Small Filler
Size: 1/2" x 1 3/4"
Lengths: 2-12' long
Matching Handrail: to fit handrail #4001
#4004 2 3/4" Handrail - no groove
Size: 1 3/4" x 2 3/4"
Lengths: 2- 12', occasionally 14'-16'
No groove: designed for dowel-topped spindles or metal balusters that do not use a groove for installation. Holes are drilled in the underside to accept the round end of the wood or metal spindles.
#4900 Modern Handrail (grooved for 1 5/16" spindles)
 |
#4900 Modern Handrail, with groove
Size: 1 5/8" x 4 1/2" (but can be made any size) Groove: 1 5/16" uses filler #4210 #4901 Modern Handrail, no groove
Same as above but no groove |
#4230 Shoe Rail (grooved for 1 5/16" spindles)
Size: 3/4" x 2 3/4"
Groove: 1 5/16" uses filler #4210
Application: Use as a bottom rail on the floor to accept the end of the spindles, especially in a retrofit application where you do not have a dowel pin on the end of your spindles, and this represents an easier solution than trying to re-dowel your balusters.
#4221 Base Rail: 3/4" x 3 1/4"
Size: 3/4" x 3 1/4"
Application: mounted on the floor to accept the doweled-end of the spindles for horizontal railings.
Use a narrower spacer underneath the base rail to lift it up, if you would like it to float over the top of carpet, tile, laminate or vinyl. If you use a spacer say only 2 3/4" wide, when the base rail is mounted on top of the spacer it will create a notch on the flooring size to accept the flooring of choice. Make the spacer a thickness equal to the thickness of your flooring.
#4240 2-Sided Stringer Cap (grooved 1 15/16" )
Size: 5/8" x 2 1/2"
Groove: 1 15/16" (for 1.5" stringer + two layers of 1/4" plywood, but since 1/4" plywood is NOT 1/4" thick, but rather a thinner metric equivalent) we have made this slightly narrower)
Application: This moulding caps off top edge of exposed stringer and the decorative plywood applied to each side, when both sides of your stringer is exposed in the middle of an entrance.
#4241 1-Sided Stringer Cap (grooved 1 3/4" )
Size: 5/8" x 2"
Groove: 1 3/4" (1.5" stringer + 1/4" plywood facing)
Application: This moulding caps off the top edge of exposed stringer, when it is butted up tight against a wall.
#1801 4 1/4" Floor Nosing
Size: 1" x 4 1/4"
Application: To use at the lower lip of your railing opening.. in lieu of a "base rail". It comes in a number of different sizes and designs. This one includes a "groove" to match traditional hardwood flooring, but it is also available with an overslung lip for laminate.. more information on floor mouldings
#3400 Wall Mount Handrail Brackets
Size: new handrail brackets in stock DO NOW comply with new Ontario Building Code Regulations that demand that All wall mounted handrails must have 2" between the wall and the inside edge of the handrail.
We have these in stock in both red oak and maple. They are predrilled to attach to the wall and to attach to the handrail and require 1/2" mushroom caps to hide screw holes.
|
Save to: |
